Search found 1668 matches
- Tue Jun 03, 2014 5:38 pm
- Forum: Solo
- Topic: rent or borrow a trailer for the Z06... Peru tour and nation
- Replies: 13
- Views: 5138
Re: rent or borrow a trailer for the Z06... Peru tour and na
How wide is a Z06 from outside of tire to outside of tire? My trailer is kind of narrow. Our Geo barely fits on it. I don't really plan to go to Peru or Nationals. I'd have to double check that I don't have a need for it those days.
- Sun Jun 01, 2014 8:00 pm
- Forum: SCCA General Discussion
- Topic: From SCCA National - No Drones
- Replies: 46
- Views: 10601
Re: From SCCA National - No Drones
Property owners own the first 450 ft of airspace above their property, so someone could claim trespassing. Now, if they're over 450ft, it's up to the FAA to enforce it. That is highly unlikely to happen. How could we even determine elevation of an aircraft? There are so many problems with enforcing ...
- Tue May 27, 2014 8:39 pm
- Forum: SCCA General Discussion
- Topic: From SCCA National - No Drones
- Replies: 46
- Views: 10601
Re: From SCCA National - No Drones
So, can I fly my RC-controlled multi-rotor copter at an event as long as I stay off of the course? I had fully intended to do some aerial video at an event sometime. Sounds like that might be out of the question now. In general, I don't think we have much to worry about. It's by far the exception th...
- Fri May 23, 2014 7:15 am
- Forum: SCCA General Discussion
- Topic: Pipe Bender?
- Replies: 10
- Views: 2479
Re: Pipe Bender?
I like Scott's idea. Whichever you choose, let us know how it turns out.
- Thu May 22, 2014 12:13 pm
- Forum: SCCA General Discussion
- Topic: Pipe Bender?
- Replies: 10
- Views: 2479
Re: Pipe Bender?
You might have some trouble with it only being 7" long. You wouldn't have much left to hold on to at either end. At 20 degrees of angle, I bet you wouldn't get too much crush using a typical "crush" bender.
- Mon May 19, 2014 12:13 pm
- Forum: SCCA General Discussion
- Topic: Driving suggestions: Thru Nashville or Lex and Louisville?
- Replies: 6
- Views: 1976
Re: Driving suggestions: Thru Nashville or Lex and Louisvill
Nashville isn't as bad as Atlanta...usually. Especially since you're going to the north side of Nashville, I wouldn't be too concerned. There will definitely be increased traffic, and you'll take a little more time to get through. But, you shouldn't expect any stop/go unless there is an accident. Al...
- Mon May 12, 2014 9:54 am
- Forum: SCCA Classifieds
- Topic: Dad is selling his 1989 Honda Civic Si. Ready to race.
- Replies: 8
- Views: 4855
Re: Dad is selling his 1989 Honda Civic Si. Ready to race.
I see this car a lot since I drive past the guy's house several times per day. It does look pretty good. Exhaust is kind of loud though for daily duty. Looks like a good deal for someone wanting to be competitive with little effort (mechanically).
- Mon May 12, 2014 9:52 am
- Forum: SCCA Classifieds
- Topic: Dad is selling his 1989 Honda Civic Si. Ready to race.
- Replies: 8
- Views: 4855
Re: Dad is selling his 1989 Honda Civic Si. Ready to race.
Technicallysteverife wrote:As a FYI, the Ingalls front adjusters are not ST legal.
- Wed May 07, 2014 9:19 pm
- Forum: SCCA Classifieds
- Topic: APTUS is Hiring
- Replies: 0
- Views: 2045
APTUS is Hiring
APTUS DesignWorks is looking to hire an engineer/designer or two. APTUS is East Tennessee's best and most awesome design and engineering firm. We do product development and design of industrial automated machinery. For more info about APTUS, visit http://www.aptusdesignworks.com. We have been lookin...
- Sun Apr 27, 2014 3:42 pm
- Forum: SCCA General Discussion
- Topic: Need 1/4" ID Pipe Bead Rolled ASAP
- Replies: 25
- Views: 5744
Re: Need 1/4" ID Pipe Bead Rolled ASAP
I'd be surprised if anyone around here could TIG that without partially or fully obstructing the fluid path. Since it's stainless, you could probably weld it without using any fill rod. If you blend it together, there should be no obstruction inside the tube. ^^Opinion of someone that is not a weld...
- Sun Apr 27, 2014 3:39 pm
- Forum: SCCA General Discussion
- Topic: Need 1/4" ID Pipe Bead Rolled ASAP
- Replies: 25
- Views: 5744
Re: Need 1/4" ID Pipe Bead Rolled ASAP
disneyd wrote:I can make a double flare. Everyone think that would work for a coolant line?
The first step of the double flare looks basically like what you're showing there.
- Sun Apr 27, 2014 3:38 pm
- Forum: SCCA General Discussion
- Topic: Need 1/4" ID Pipe Bead Rolled ASAP
- Replies: 25
- Views: 5744
Re: Need 1/4" ID Pipe Bead Rolled ASAP
For coolant, you'd probably be fine without a bead at all. A hose clamp on smooth pipe would be plenty. Your coolant system is probably pressurized to 14 psi. The largest cross section of the fluid at the joint is the OUTSIDE diameter of the tube. At 5/16", that's .077 square inches cross secti...
- Mon Apr 14, 2014 7:37 pm
- Forum: SCCA Classifieds
- Topic: Needing a Water Temp Gage
- Replies: 1
- Views: 1166
Needing a Water Temp Gage
Anyone have an extra water temp gage laying around for a reasonable price? We need a new one for the Geo. The current one is only visible at night, and we mostly don't race at night.
- Mon Apr 14, 2014 1:20 pm
- Forum: Solo
- Topic: Wilmington Report
- Replies: 24
- Views: 4832
Re: Wilmington Report
Do they allow camping on site there?
- Tue Apr 01, 2014 12:36 pm
- Forum: ETRSCCA Business & Announcements
- Topic: ~~~~~ Monthly Meeting~~~~~
- Replies: 6
- Views: 4196
Re: ~~~~~ Monthly Meeting~~~~~
Oops. Nevermind. I'm an April fool.