March 29-31 zMax Match Tour
-
- Posts: 8798
- Joined: Fri Dec 05, 2003 11:05 am
Re: March 29-31 zMax Match Tour
no.. larger
ETR Pro Class Champion-2002-03-10-11-12-13-14-15
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
-
- Posts: 1503
- Joined: Wed Nov 02, 2011 4:19 pm
- Location: Kingsport, TN
Re: March 29-31 zMax Match Tour
JB,
By uncalibrated eyeball, it looks like there's a lot of vertical suspension travel. What's the motion ratio of the front springs, i.e. what's the actual wheel rate?
By uncalibrated eyeball, it looks like there's a lot of vertical suspension travel. What's the motion ratio of the front springs, i.e. what's the actual wheel rate?
DeWitt Payne
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
-
- Posts: 8798
- Joined: Fri Dec 05, 2003 11:05 am
Re: March 29-31 zMax Match Tour
the whole range used in the video is appx 1.75 inches.... I dont know if less would be good... (?)
ETR Pro Class Champion-2002-03-10-11-12-13-14-15
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
Re: March 29-31 zMax Match Tour
NO less would be bad, a certain amount of travel is needed or you hit the stops hard and unload the suspension....
JY ( Jeff ) Cox
ETR R.E
2018-2021, 2022, 2023 Solo Nationals Co Chairman
2010 GT500
ETR R.E
2018-2021, 2022, 2023 Solo Nationals Co Chairman
2010 GT500
Re: March 29-31 zMax Match Tour
I think DeWitt is asking why John isn't running stiffer springs, which isn't the same thing as travel.
Chris Harp
2009 Mazda RX-8 | 2018 Toyota Tundra | 2011 BMW M3
2009 Mazda RX-8 | 2018 Toyota Tundra | 2011 BMW M3
-
- Posts: 8798
- Joined: Fri Dec 05, 2003 11:05 am
Re: March 29-31 zMax Match Tour
700 thinking about going stiffer.. but not sure the dampers would handle much more.
It looks fairly controlled to me.. no sharp movements nor po=going...
would be interesting to see JY or Randys cars motions from a similar angle
It looks fairly controlled to me.. no sharp movements nor po=going...
would be interesting to see JY or Randys cars motions from a similar angle
ETR Pro Class Champion-2002-03-10-11-12-13-14-15
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
-
- Posts: 1503
- Joined: Wed Nov 02, 2011 4:19 pm
- Location: Kingsport, TN
Re: March 29-31 zMax Match Tour
NO less would be bad, a certain amount of travel is needed or you hit the stops hard and unload the suspension....
Well, yes, more or less. You can see from the video that JB is barely, if at all, touching the bump stop at full compression. Putting in a stiffer spring at the same ride height would reduce travel and be even further away from the stop at full compression. Or you could lower the car some more if that doesn't move to a bad part of the camber gain curve or add bump steer.I think DeWitt is asking why John isn't running stiffer springs, which isn't the same thing as travel.
It depends on the quality of your suspension geometry, but generally less is better until the tires won't stay planted. Of course you could stand a higher spring rate at zMax than you could at Bristol because zMax is pretty smooth. As I remember, BFG's don't like camber change relative to the ground in roll. With a lowered McPherson strut suspension like mine you need a lot of spring and bar to minimize roll. Increased front roll stiffness can actually increase grip enough to at least partially make up for the increased weight transfer to the front wheels and make the car be able to go faster.the whole range used in the video is appx 1.75 inches.... I dont know if less would be good... (?)
The motion ratio for my car is pretty close to 1. My mechanic runs 600 lbs/inch front springs in his NASA American Iron S197 Mustang, which gives a wheel rate of about 540 lbs/in and the bar probably adds another 400 lbs/in or so. I've dropped back to 475 lbs/inch front springs from 550 because I thought it was a bit too harsh. If I heard correctly, however, Loughlin was running 700 lbs/in front springs in his S550 Mustang at zMax with, I think, similar front suspension geometry to mine.
DeWitt Payne
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
-
- Posts: 1503
- Joined: Wed Nov 02, 2011 4:19 pm
- Location: Kingsport, TN
Re: March 29-31 zMax Match Tour
700 thinking about going stiffer.. but not sure the dampers would handle much more.
Can you put in a bigger anti-roll bar?
DeWitt Payne
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
-
- Posts: 1503
- Joined: Wed Nov 02, 2011 4:19 pm
- Location: Kingsport, TN
Re: March 29-31 zMax Match Tour
I see the Challenger has an SLA suspension so the motion ratio is going to be significantly less than 1. Since the wheel rate is the spring rate times the square of the motion ratio, the wheel rate is going to be a lot less than 700 lbs/inch. Here's a link to a short article about calculating spring rates:
http://www.worksevo.com/Spring_Rates_1.pdf
My calculated front suspension frequency is 2.1Hz with 475 lbs/inch springs. With 700 lbs/inch springs, it would be 2.6Hz. For a car with almost no aero, that's about the upper practical limit. I don't think I'd want to drive it on the street every day, though. My guess would be that to get your ride frequency above 2 Hz, you're going to need a lot stiffer springs and shocks.
http://www.worksevo.com/Spring_Rates_1.pdf
My calculated front suspension frequency is 2.1Hz with 475 lbs/inch springs. With 700 lbs/inch springs, it would be 2.6Hz. For a car with almost no aero, that's about the upper practical limit. I don't think I'd want to drive it on the street every day, though. My guess would be that to get your ride frequency above 2 Hz, you're going to need a lot stiffer springs and shocks.
DeWitt Payne
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
2011 Mustang GT CAM-C
"Tires are meant to die young." Heyward Wagner
Re: March 29-31 zMax Match Tour
That's really good.Kinetic wrote: ↑Mon Apr 02, 2018 11:00 pm Here is my fastest run from the Charlotte Match Tour during the first round of the underdog challenge Saturday.
https://youtu.be/Bm7nLTZVcPg
'16 FRS - PSTX 97
Re: March 29-31 zMax Match Tour
x2... definitely liked the finish slalom. The mid engine cars are so much fun in elements like that.
Sent from my SM-G930P using Tapatalk
Sent from my SM-G930P using Tapatalk
Mark Pilson
03 Z06 - Sword
09 Mustang - Club
01 Excursion - The safe you dropped from the 10th story
03 Z06 - Sword
09 Mustang - Club
01 Excursion - The safe you dropped from the 10th story
Re: March 29-31 zMax Match Tour
Yeah, Adam Norton and I talked about how much fun that course would have been in our Spyders.
'16 FRS - PSTX 97
-
- Posts: 8798
- Joined: Fri Dec 05, 2003 11:05 am
Re: March 29-31 zMax Match Tour
Dewitt... your right.. I did only hit the bump stops once..maybe.. but, thats also one of the smoothest lots we will ever run on..maybe short of Wilmington. I actually softened up the front bar a hole.. and the turn in was a tad better.
My next area of attention is the upper arm bushing change.. and attempt to cut the castor in half.. Its actual current castor is 9.5.. I want to get near 6.5 degrees.
My next area of attention is the upper arm bushing change.. and attempt to cut the castor in half.. Its actual current castor is 9.5.. I want to get near 6.5 degrees.
Last edited by John Brown on Wed Apr 04, 2018 6:36 am, edited 1 time in total.
ETR Pro Class Champion-2002-03-10-11-12-13-14-15
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
-
- Posts: 8798
- Joined: Fri Dec 05, 2003 11:05 am
Re: March 29-31 zMax Match Tour
yes! even in the big Dodge, that finish salom was fun.. to see how early you could maash it to the floor!
that shit leading up to the finish salom.....
going out was fun... coming back was one of the worst examples of "flowing: I have ever done on a National course.
ETR Pro Class Champion-2002-03-10-11-12-13-14-15
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C
BMW/CCA D-Mod National Road Racing Champion-2011
Pro-Solo Prepared National Champ-2004
Pro-Solo Prepared National Champ-2005
2016 Dodge Challenger SRT 6.4L CAM-C