Car Setup Help

[MARKP]

Just adding a data point to the discussion, when I want to poly and delrin on the old FSP car, I got a lot more noise in the suspension and car during street use. Because of this, when I built the Camaro, I went with new rubber bushings on the control arms since I planned on driving it on the street and it not being just a race car.

[Buck05Sti]

Just adding a data point to the discussion, when I want to poly and delrin on the old FSP car, I got a lot more noise in the suspension and car during street use. Because of this, when I built the Camaro, I went with new rubber bushings on the control arms since I planned on driving it on the street and it not being just a race car.

A lot more noise in what respect? I feel like i could probably tolerate a fair amount, but this certainly isnt strictly race kawr

[MARKP]

Noise over bumps, general harshness in the suspension.

[dewittpayne]

general harshness in the suspension.

Isn't that the point of using delrin bushings? Harshness and faster response are two sides of the same coin.

[TedV]

A lot more noise in what respect? I feel like i could probably tolerate a fair amount, but this certainly isnt strictly race kawr

With the roads around knoxville, imagine loading your clothes dryer with various sizes of rocks. Run it and sit on the dryer. Some might like it.

[Buck05Sti]

A lot more noise in what respect? I feel like i could probably tolerate a fair amount, but this certainly isnt strictly race kawr

With the roads around knoxville, imagine loading your clothes dryer with various sizes of rocks. Run it and sit on the dryer. Some might like it.

Dont you threaten me with a good time!

[Buck05Sti]

Noise over bumps, general harshness in the suspension.

Im not too concerned about noise, but i take it you mean the ride became noticeably rougher?

[steverife]

There is a lot of downside to delrin (noise, harshness, binding), but not really a lot of upside on a street tired street car.

[Buck05Sti]

There is a lot of downside to delrin (noise, harshness, binding), but not really a lot of upside on a street tired street car.

new rubber it is!

[MARKP]

There is a lot of downside to delrin (noise, harshness, binding), but not really a lot of upside on a street tired street car.

new rubber it is!

Bucky likes rubbers! Uhh, you know what I mean.

[DBOWMANEOD]

I'm in the grey 2015 sti from last season. I bought the whiteline kit for mine. Endlinks and bushings came with it. I daily mine. I also run the RCE yellow springs. It's not to bad or noisy at all. You can check it out on the 6th if you want. Keep the subie!

[Buck05Sti]

I'm in the grey 2015 sti from last season. I bought the whiteline kit for mine. Endlinks and bushings came with it. I daily mine. I also run the RCE yellow springs. It's not to bad or noisy at all. You can check it out on the 6th if you want. Keep the subie!

I wouldnt mind taking a look underneath, as im sure my parts wont be here yet. Did you install the bars? If so, how hard was it?

[DBOWMANEOD]

Yes a buddy of mine and myself installed sway bars end links and the extra braces on the rear. You're welcome to check it out.

[Buck05Sti]

Yes a buddy of mine and myself installed sway bars end links and the extra braces on the rear. You're welcome to check it out.

How hard was the install? Id like to do mine myself, but im working with a gravel driveway, although, i could use the street too My bars should be here by the weekend

[DBOWMANEOD]

We had a jack and had each end of the car on stands. We did everything in one day. It's not as hard as my downpipe was